PRO 35

Cardioid Condenser Clip-on Instrument Microphone

MSRP* US$219.00
Two-Year Limited End-User Warranty

*Manufacturer's Suggested Retail Price. Actual selling price may vary; please check with an authorized Audio-Technica dealer.



  • Overview
  • Features
  • Specifications
  • Downloads
  • Reviews
  • Q & A

  • Overview


    Designed for sax, toms, brass and percussion, the PRO 35 excels in high-SPL applications and is ideal for active stage performances. Its extended frequency response captures subtle nuances of the performance. The included UniMount® clip permits accurate positioning and provides shock resistance while protecting the element. The microphone’s cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of the desired sound source.
  • Features

    • UniMount® clip permits accurate positioning, provides shock resistance and protects element

    • Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source

    • Extended frequency response captures subtle nuances of the performance

    • 6' (1.8 m) cable permanently attached to microphone



  • Specifications

    ELEMENTFixed-charge back plate, permanently polarized condenser
    POLAR PATTERNCardioid
    FREQUENCY RESPONSE50-15,000 Hz
    LOW FREQUENCY ROLL-OFF80 Hz, 18 dB/octave
    OPEN CIRCUIT SENSITIVITY-45 dB (5.6 mV) re 1V at 1 Pa
    IMPEDANCE250 ohms
    MAXIMUM INPUT SOUND LEVEL145 dB SPL, 1 kHz at 1% T.H.D.
    DYNAMIC RANGE (typical)115 dB, 1 kHz at Max SPL
    SIGNAL-TO-NOISE RATIO64 dB, 1 kHz at 1 Pa
    PHANTOM POWER REQUIREMENTS11-52V DC, 2 mA typical
    SWITCHFlat, roll-off
    WEIGHT (MICROPHONE)0.3 oz (8 g)
    WEIGHT (POWER MODULE)2.9 oz (81 g)
    DIMENSIONS (MICROPHONE)0.98" (25.0 mm) long,
    0.40" (10.2 mm) diameter
    DIMENSIONS (POWER MODULE)3.66" (92.9 mm) long,
    0.74" (18.9 mm) diameter
    OUTPUT CONNECTOR (POWER MODULE)Integral 3-pin XLRM-type
    CABLE6.0' (1.8 m) long (permanently attached to microphone), 0.10" (2.6 mm) diameter, 2-conductor, shielded cable with TA3F-type connector
    ACCESSORIES FURNISHEDAT8418 UniMount® microphone instrument mount; AT8538 power module; soft protective pouch
    AUDIO-TECHNICA CASE STYLEM12
    Click on the chart to view the larger image
    POLAR PATTERN
    POLAR PATTERN
    FREQUENCY RESPONSE
    FREQUENCY RESPONSE



    Conditions
  • Downloads

    PRO 35 Specification Sheet (pdf 356.40 KB)
    PRO 35 Submittal Sheet (pdf 362.08 KB)
    Optional Windscreens / Mounts
  • Reviews

    REVIEW SNAPSHOT®

    by PowerReviews
    Audio-TechnicaPRO 35 Cardioid Condenser Clip-on Instrument Microphone
     
    5.0

    (based on 2 reviews)

    Ratings Distribution

    • 5 Stars

       

      (2)

    • 4 Stars

       

      (0)

    • 3 Stars

       

      (0)

    • 2 Stars

       

      (0)

    • 1 Stars

       

      (0)

    Reviewed by 2 customers

    Displaying reviews 1-2

    Back to top

     
    5.0

    Great sounding on Alto and Tenor

    By 

    from Los Angeles, CA, USA

    Site Member

    Pros

    • Brass
    • woodwinds

    Cons

    • thin sound on plam keys but still cuts through

    Best Uses

      Comments about Audio-Technica PRO 35 Cardioid Condenser Clip-on Instrument Microphone:

      I have used the PRO35 for five years now. I've played with it in both large and small venue with great results.
      I have the hard wired and the cordless. Both sound great. Sound is a little thin on the palm keys on my Soprano. I highly recommend this mic.

      • What best describes the environment the product was used in?:
      • Intermediate
      • What best describes your level of audio knowledge?:
      • Live Sound
      • How long have you used this product?:
      • Over a year
      • Reliability:
      •  
      • Audio Quality:
      •  
      • Durability:
      •  
      • Ease of Use:
      •  
       
      5.0

      the best sound that i ever get from brass

      By 

      from venezuela

      Site Member

      Pros

      • Brass
      • Drums
      • percussion

      Cons

        Best Uses

          Comments about Audio-Technica PRO 35 Cardioid Condenser Clip-on Instrument Microphone:

          the best sound that can be picked from any brass instrument is using an pro35 or atm350 clip on microphones. always clean with excellent transients, excelent positioning, excellent feedback resistance, fully naturally, uncoloured sound, precise!!! always the best! my musicians on stage once hear your instruments with these mics, they fall in love! five stars!!!

          • What best describes the environment the product was used in?:
          • Expert
          • What best describes your level of audio knowledge?:
          • Live Sound
          • How long have you used this product?:
          • Over a year
          • Reliability:
          •  
          • Audio Quality:
          •  
          • Durability:
          •  
          • Ease of Use:
          •  

          Displaying reviews 1-2

          Back to top

        • Q & A

          Do you have questions about this product?

          Get answers from real customers and in-house experts with AnswerBox.

          38 Questions | 38 Answers
          Displaying questions 1-10Previous | Next »
          • Q:

            pro35cw vs. pro350cw sound quality difference, used on tenor sax ?
            Asked on 1/2/2016 by SAL from Tamaqua,PA

            1 answer

            • CUSTOMER CARE

              A:

              To receive an answer to your question, please contact the Audio-Technica United States (ATUS) Audio Solutions Team at:
              audio-solutions@atus.com

              Thanks!

              Answered on 1/5/2016 by ATUS_Specialist2 from Stow, OH
          • Q:

            This mic works for clarinet to?
            Asked on 12/28/2015 by Hrt from New york new york

            1 answer

            • Staff Reviewer

              A:

              Yes, it may be used for mike a clarinet.

              Answered on 12/31/2015 by ATUS_Specialist3
          • Q:

            If the speaker does not have phantom power i need to conect through something that does-such as a DI or someth ing...correct? Any suggestions?
            Asked on 12/5/2015 by Newb

            1 answer

            • Staff Reviewer

              A:

              You may use an external phantom power supply such as the AT8801. You may also use the AT8531 power module instead of the AT8538 power module. This would allow you to use a battery in the power module to provide the proper power to the microphone.

              Answered on 12/13/2015 by ATUS_Specialist3
          • Q:

            will this mic work with your system 10 wireless system
            Asked on 11/9/2015 by trsax from gloucester va

            1 answer

          • Q:

            I need a new windscreen for an at35, how do I get one or a few?
            Asked on 11/7/2015 by Justin from United States

            1 answer

            • Staff Reviewer

              A:

              Please contact our Audio Solutions Department at (330) 686-2600 ext 5000 or at audio-solutions@atus.com for assistance with this.

              Answered on 11/9/2015 by ATUS_Specialist3
          • Q:

            Hi! I bought accidentally the wireless version. Does exist any adaptor/connector that can turn the ATM PRO35cW (wirelss) into a PRO35 (cable)?
            Thanks in advance!
            Best regards
            Marco
            Asked on 9/23/2015 by Marco sax from Italy

            1 answer

            • Staff Reviewer

              A:

              Yes, you may use the AT8539 power module to properly adapt the PRO35cW (with 4 pin HRS connector) to a PRO35 (with a standard XLR connection.)

              Answered on 9/24/2015 by ATUS_Specialist3
          • Q:

            I bought the wireless version PRO35wC. I didn't know I need to buy a wireless system separately. Now there are so many choices I don't know what to do! I bought this to play saxophone on gigs, what do you recommend?
            Asked on 9/3/2015 by Wholeladoflove from Los Angeles, CA

            1 answer

            • Staff Reviewer

              A:

              Thank you for your inquiry. There are two versions of this mic. The Pro 35 is a wired version with an XLR connector and the Pro 35cW is a version to be used with an Audio-Technica wireless system. Since there are many options I suggest that you contact our Audio Solutions team at 330-686-2600 ext 5000 and discuss your needs.

              Answered on 9/9/2015 by AudioSolutionsManager from Audio-Technica U.S., Inc.
          • Q:

            I would like to use this mic and input to iPad, will the Tascam iXZ work?
            Asked on 9/1/2015 by cwc from Andover,MA

            1 answer

            • Staff Reviewer

              A:

              The Pro 35 will work in this setup. The attached cable on the PRO 35 terminates into a TA3f (or mini XLR) connection. This then plugs into the included power module and converts that connection to an XLR, which you can then plug into your Tascam.

              Answered on 9/3/2015 by ATUS_Specialist4
          • Q:

            Can one get an adaptor to a standard guitar jack?

            the present microphone hookup works good but I have a pre-amp I use with fiddle -- a Fishman Pro-Eq Platinu -- and the only input for the fishman is a standard larger guitar jack. Wondered if the connector on the mic, which also seems to have a small 3-pin connector also, could be adapted somehow.
            thanks,
            paul
            Asked on 7/20/2015 by pablo

            1 answer

            • A:

              Please contact our Audio Solutions Department at (330) 686-2600 ext 5000 or at audio-solutions@atus.com for assistance with this.

              Answered on 7/31/2015 by AudioSolutionsSpec3
          • Q:

            How do I get my Pro 35 into my fuzz pedal?

            I want to put an XLR to 1/4 Inch cable on my Pro 35 so I can run it through my fuzz pedal. Can this be done?
            Asked on 1/5/2015 by eggchairjim from Oregon, USA

            1 answer

            • A:

              You will need to provide the proper voltage to the PRO35 microphone with the AT8531 power module which can power the microphone via a AA battery.

              Depending on the specs of your Fuzz Pedal, you may need to adapt your MIC level signal to LINE level in the CP8201 Impedance Matching Transformer.

              Answered on 1/7/2015 by AudioSolutionsSpec3
          Displaying questions 1-10Previous | Next »

          Do you have a question about this product?