Audio-Technica Menu

PRO 47T

ProPoint® Cardioid Condenser Thread-mount Gooseneck Microphone


U.S. Two-Year Limited End-User Warranty

*Manufacturer's Suggested Retail Price. Actual selling price may vary; please check with an authorized Audio-Technica dealer.



  • Overview
  • Features
  • Specifications
  • Downloads
  • Reviews
  • Q & A

  • Overview


    This double-gooseneck cardioid condenser microphone with integral power module and 5/8"-27 adapter-mount is ideal for boardroom, school, government, house of worship and other installed applications. Featuring a wide-range condenser element with low-mass diaphragm for superior performance, the microphone's self-contained electronics eliminate need for external power modules. Available in two lengths: 12.40" (PRO 47T) and 15.79" (PRO 47TL).
  • Features

    • Wide-range condenser element with low-mass diaphragm for superior performance

    • Self-contained electronics eliminate need for external power modules

    • Flat, smooth frequency response

    • Quiet, fixed-placement, long-life gooseneck

    • Direct mounts to any 5/8"-27 stand, or to included threaded mounting stud

    • 9.8' (3.0 m) cable permanently attached between microphone and XLRM-type connector

    • Overall length of 12.40" (315.0 mm)

    • Also available in a 15.79" (401.0 mm)-long version as PRO 47TL

  • Specifications

    ELEMENTFixed-charge back plate, permanently polarized condenser
    POLAR PATTERNCardioid
    FREQUENCY RESPONSE70-16,000 Hz
    OPEN CIRCUIT SENSITIVITY-37 dB (14.1 mV) re 1V at 1 Pa
    IMPEDANCE100 ohms
    MAXIMUM INPUT SOUND LEVEL134 dB SPL, 1 kHz at 1% T.H.D.
    DYNAMIC RANGE (typical)106 dB, 1 kHz at Max SPL
    SIGNAL-TO-NOISE RATIO66 dB, 1 kHz at 1 Pa
    PHANTOM POWER REQUIREMENTS9-52V DC, 2 mA typical
    WEIGHT2.2 oz (63 g)
    DIMENSIONS12.40" (315.0 mm) long,
    0.47" (12.0 mm) head diameter
    OUTPUT CONNECTOR3-pin XLRM-type on cable
    CABLE9.8' (3.0 m) cable permanently attached between microphone and XLRM-type connector
    ACCESSORIES FURNISHEDAT8146 windscreen; AT8425 5/8"-27 threaded mounting stud
    AUDIO-TECHNICA CASE STYLEM22
    Click on the chart to view the larger image
    POLAR PATTERN
    POLAR PATTERN
    FREQUENCY RESPONSE
    FREQUENCY RESPONSE



    Conditions
  • Downloads

    PRO 47T, PRO 47TL Specification Sheet (pdf 87.38 KB)
    PRO 47T & PRO 47TL Submittal Sheet (pdf 373.79 KB)
    Optional Windscreens / Mounts
  • Reviews

  • Q & A

    Hi, The previous user of my microphone attached a 1/4 inch jack. This is a problem to me as a cannot find a phantom power supply online of this size. Also, I tested the microphone with a multimeter before I realized it needed phantom power. I set my multimeter to 2k ohms and it did not short on any of the pins. Is this normal for a mic that needs a phantom supply? Just to be clear, it was NOT plugged in to phantom. Any advice would be appreciated.

    Tom

    Please contact our Audio Solutions Department at (330) 686-2600 ext 5000 or at audio-solutions@atus.com for assistance with this.

    ATUS_Specialist3

    Hi, I have this microphone, with a 1/4 inch jack. I think the person who used this before me soldered it on as there is some heatshrink tubing where the wire comes out of the base. For some odd reason, no sound comes out of the unit when connected to a guitar amp! Am I doing something wrong? It is connected to 'Line'

    Tom

    Yes, two things. 1. Being a condenser microphone, the PRO47T requires phantom power to operate. http://blog.audio-technica.com/audio-solutions-question-of-the-week-what-are-the-differences-between-the-microphones-that-audio-technica-offers-part-3/ 2. Plugging a MIC level signal (such as that from a microphone) will not work into a LINE level input, such as a guitar amplifier. Please contact our Audio Solutions Department at (330) 686-2600 ext 5000 or at audio-solutions@atus.com for assistance with this.

    ATUS_Specialist3

    is this mic wired and is is this mic wired and do i need to buy any other parts to mount it to a podium

    Ericinc

    The PRO 47T is a wired microphone, it connects to the associated audio system via a standard 3-pin XLR male type output connector on the end of its attached 9.8 foot cable. A threaded mounting stud is provided for mounting the microphone to a podium. The stud can be seen at the following link. It is approximately 1 inch in length. http://www.audio-technica.com/cms/windscreens_mounts/ac96344d4fc70467/index.html

    AudioSolutionsSpec1