Audio-Technica Menu

PRO 49QL

ProPoint® Cardioid Condenser Quick-mount Gooseneck Microphone


U.S. Two-Year Limited End-User Warranty

*Manufacturer's Suggested Retail Price. Actual selling price may vary; please check with an authorized Audio-Technica dealer.



  • Overview
  • Features
  • Specifications
  • Downloads
  • Reviews
  • Q & A

  • Overview


    The PRO 49QL quick-mount double-gooseneck cardioid condenser microphone is designed to plug into any standard XLRF-type surface or cable connector. With a flat, smooth frequency response and self-contained electronics, this mic features a quiet, fixed-placement, long-life gooseneck and wide-range condenser element with low-mass diaphragm for superior performance. Available in two lengths: 13.07" (PRO 49Q); 16.46” (PRO 49QL).
  • Features

    • Wide-range condenser element with low-mass diaphragm for superior performance

    • Self-contained electronics eliminate need for external power modules

    • Flat, smooth frequency response

    • Quiet, fixed-placement long-life gooseneck

    • Plugs into any standard XLRF-type surface or cable connector

    • Overall length of 16.46" (418.0 mm)

    • Also available in a 13.07" (332.0 mm)-long version as PRO 49Q

  • Specifications

    ELEMENTFixed-charge back plate, permanently polarized condenser
    POLAR PATTERNCardioid
    FREQUENCY RESPONSE70-16,000 Hz
    OPEN CIRCUIT SENSITIVITY-37 dB (14.1 mV) re 1V at 1 Pa
    IMPEDANCE100 ohms
    MAXIMUM INPUT SOUND LEVEL134 dB SPL, 1 kHz at 1% T.H.D.
    DYNAMIC RANGE (typical)106 dB, 1 kHz at Max SPL
    SIGNAL-TO-NOISE RATIO66 dB, 1 kHz at 1 Pa
    PHANTOM POWER REQUIREMENTS9-52V DC, 2 mA typical
    WEIGHT3.0 oz (84 g)
    DIMENSIONS16.46" (418.0 mm) long,
    0.47" (12.0 mm) head diameter,
    0.74" (18.9 mm) base diameter
    OUTPUT CONNECTORIntegral 3-pin XLRM-type
    ACCESSORY FURNISHEDAT8146 windscreen
    AUDIO-TECHNICA CASE STYLEM23
    Click on the chart to view the larger image
    POLAR PATTERN
    POLAR PATTERN
    FREQUENCY RESPONSE
    FREQUENCY RESPONSE



    Conditions
  • Downloads

    PRO 49Q, PRO 49QL Specification Sheet (pdf 67.35 KB)
    PRO 49Q & PRO 49QL Submittal Sheet (pdf 360.02 KB)
    Optional Windscreens / Mounts
  • Reviews

  • Q & A

    can you please locate me where is your store in delhi India or specially in Ranchi,Jharkhand,India or any retailer selling your product

    vikas

    You may contact Audio-Technica India for further assistance. enquiry@audio-technica.co.in

    ATUS_Specialist3

    I have a mixing board with 48 VDC phantom power supply (switch and indicator light are on; connected through standard, functioning XLR mic cable), but my new PRO 49QL is not working out of the box. Do I need an additional power module to get the mic to work? Or is there reason to believe it was broken in shipping?

    Bob

    Thank you for your inquiry. Can you verify that phantom power is present? You can do this by either connecting another condenser microphone to see if it works, or by using a volt meter to check the power. You could also try the microphone on another mixing console, possibly at a music store if you do not have access to one. Also, make sure that you are using an XLR male to XLR female cable. If none of this resolves the issue you may have a faulty microphone. Please contact the Service Department at 330-686-2600 option 4. They will be happy to help with this.

    AudioSolutionsManager

    Can you buy the microphone sponge cover for the Pro49QL?

    Jim

    Yes, it is the AT8146 Windscreen.

    ATUS_Specialist1

    Does this need phantom power ? Audio-Technica PRO 49QL - Does this need phantom power ?

    kandy

    Yes it does. All condenser element type microphones require some amount of power to operate. For the PRO 49QL, this would be supplied in the form of phantom power. Phantom power must be supplied to the 3-pin male XLR output connector on the microphone. Phantom Power may be provided by a Mixer, Amplifier or Recorder that has a balanced 3-pin female XLR type Microphone input AND features phantom power of at least 9 volts (anywhere from 9 to 48 volts is acceptable). If the Mixer, Amplifier or Recorder you are connecting the microphone to does not feature phantom power, an inline phantom power supply, such as our AT8801 Single-channel 48 volt Phantom Power Supply, should be installed between the microphone and the Mixer, Amplifier or Recorder.

    AudioSolutionsSpec1

    Can the AT8662 podium mount be used with the Pro 49ql gooseneck mic?

    PopsNScratches

    For those who might be interested, I'm answering my own question. I called AT customer service and they actually tried it out. They report that the Pro 49ql works perfectly with the AT8662 podium mount.

    PopsNScratches

    How long is the XLRF-type cable that is attached to the PRO49QL microphone? How long is the XLRF-type cable that is attached to the PRO49QL microphone?

    Manpreet

    Here are the dimensions of the PRO49QL: 16.46" (418.0 mm) long, 0.47" (12.0 mm) head diameter, 0.74" (18.9 mm) base diameter You can attach any length (copper-braided) standard XLR cable. The mic does not come with an XLR cable.

    AudioSolutionsSpec2